Searched for "24131513"
R-410A has replaced R-22 as the preferred refrigerant for use in residential and light commercial air-conditioning and heat pump systems. This is virgin gas. Only quality materials are used.
- Virgin gas
- Blended in USA
- Quality materials used
- Most common residential refrigerant
ONLY RESELLERS OR EPA-CERTIFIED TECHNICIANS CAN PURCHASE THIS PRODUCT. YOU MUST PROVIDE PROOF OF CERTIFICATION PRIOR TO ORDERING THIS REFRIGERANT PRODUCTâ€
- This refrigerant isn’t available in all locations, so please inquire about availability prior to ordering
- You can only buy R-410A refrigerant if you’re a reseller or an EPA-certified technician
- You also must provide proof of certification prior to ordering
Only resellers or EPA-certified technicians can purchase this product. you must provide proof of certification prior to ordering this refrigerant product
- Freon MO99 (R-438A) combines R-22 pressure-enthalpy characteristics with mineral oil compatibility in a unique HFC refrigerant that can be used in R-22 replacement over a wide range of evaporator temperatures. This refrigerant does not require an equipment change and can be used with mineral oil, alkyl benzene or POE oil. Refrigerant gas, n.o.s. (1,1,1,2-Tetrafluoroethane, Pentafluoroethane).
- Replaces R22 in HVAC systems
- Comparable energy performance to R22
- No equipment change required
- No oil change required
ONLY RESELLERS OR EPA-CERTIFIED TECHNICIANS CAN PURCHASE THIS PRODUCT. YOU MUST PROVIDE PROOF OF CERTIFICATION PRIOR TO ORDERING THIS REFRIGERANT PRODUCT
- Comparable capacity to R22
- Nearly identical pressures to R22
- Lower discharge temperatures
- Mineral oil compatible
- No TXV replacement required
- Copeland Discus and Bitzer approved
Only resellers or EPA-certified technicians can purchase this product. you must provide proof of certification prior to ordering this refrigerant produc. NU-22B is successfully being used in system applications ranging from residential to industrial. However, to use it safely, you must be knowledgeable in HVAC equipment refrigeration conversion to R-22 alternative refrigerant products. NU-22B Is sn EPA SNAP-Listed R-22 Replacement,ASHRAE-Designated R-422B,Okay for Use in MO-, AB-, and POE-Designed Systems. No Unnecessary Oil Changes NU-22B Has:ASHRAE Safety Classification, A1 (Nontoxic/Nonflammable)
- Greater Capacity than Its Predecessor (R-417A)
- Operating Pressures Closer to R-22 than Any Other R-22 Replacement.
- EPA SNAP-Listed R-22 replacement
- ASHRAE-designated R-422B
- ASHRAE safety classification, A1 (nontoxic/nonflammable)
- Operating pressures close to R-22
- No oil change required
ONLY RESELLERS OR EPA-CERTIFIED TECHNICIANS CAN PURCHASE THIS PRODUCT. YOU MUST PROVIDE PROOF OF CERTIFICATION PRIOR TO ORDERING THIS REFRIGERANT PRODUCT
- R-407C has the closest property match to R-22 in an air conditioning retrofit project compared to other blends on the market
- It can also be used in medium temp R-22 refrigeration systems
- R-407C has a 10 degree F temperature glide
- New systems built with R-407C must have POE lubricants, and retrofitted R-22 systems would need the residual oil flushed with POE
- Must be knowledgeable in HVAC equipment refrigeration conversion to R-22 alternative refrigerant products
Streamline Line Sets have been an industry leader for decades. We leverage our many years of experience and expertise producing copper tube in every line set we make. From liquid line and suction line handling to unique insulation applications and packaging, every Streamline Line Set meets our rigorous standards for quality and consistency. With a broad offering of liquid line and suction line diameters, insulation, thicknesses, custom ends and connections plus a wide array of custom options, we're able to meet our customers' most specialized and exacting needs.
- 3/8 in. liquid line x 3/4 in. suction line x 1/2 in. insulation x 50 ft. L
- Copper tube UL recognized to 700 psi
- R410A engineered and tested
- Proprietary manufacturing process allows for kink-free installation
- Meets ASTM B1003
ONLY RESELLERS OR EPA-CERTIFIED TECHNICIANS CAN PURCHASE THIS PRODUCT. YOU MUST PROVIDE PROOF OF CERTIFICATION PRIOR TO ORDERING THIS REFRIGERANT PRODUCT
- Only Resellers or EPA certified technicians can buy refrigerant
- You must provide proof of certification prior to ordering this R-22 refrigerant cylinder
PRO-Fit Quick Connect fittings are designed to connect refrigerant lines without an open flame, brazing or swaging. They are suitable for joining refrigerant lines in seconds. After cutting the line, deburring the ends and push to connect.
- Quick and easy push-in
- Flame-free: no flaring or brazing needed
- Single use with quick release removal
- Leak-resistant double O-rings sealing
- Compatible with major refrigerants
Streamline Line Sets have been an industry leader for decades. We leverage our many years of experience and expertise producing copper tube in every line set we make. From liquid line and suction line handling to unique insulation applications and packaging, every Streamline Line Set meets our rigorous standards for quality and consistency. With a broad offering of liquid line and suction line diameters, insulation, thicknesses, custom ends and connections plus a wide array of custom options, we're able to meet our customers' most specialized and exacting needs.
- 3/8 in. liquid line x 7/8 in. suction line x 3/8 in. insulation x 35 ft. L
- Copper tube UL recognized to 700 psi
- R410A engineered and tested
- Proprietary manufacturing process allows for kink-free installation
- Meets ASTM B1003
PRO-Fit Quick Connect fittings are designed to connect refrigerant lines without an open flame, brazing or swaging. They are suitable for joining refrigerant lines in seconds. After cutting the line, deburring the ends and push to connect.
- Quick and easy push-in
- Flame-free: no flaring or brazing needed
- Single use with quick release removal
- Leak-resistant double O-rings sealing
- Compatible with major refrigerants
Streamline Line Sets have been an industry leader for decades. We leverage our many years of experience and expertise producing copper tube in every line set we make. From liquid line and suction line handling to unique insulation applications and packaging, every Streamline Line Set meets our rigorous standards for quality and consistency. With a broad offering of liquid line and suction line diameters, insulation, thicknesses, custom ends and connections plus a wide array of custom options, we're able to meet our customers' most specialized and exacting needs.
- 3/8 in. liquid line x 3/4 in. suction line x 3/8 in. insulation x 50 ft. L
- Copper tube UL recognized to 700 psi
- R410A engineered and tested
- Proprietary manufacturing process allows for kink-free installation
- Meets ASTM B1003
Streamline Line Sets have been an industry leader for decades. We leverage our many years of experience and expertise producing copper tube in every line set we make. From liquid line and suction line handling to unique insulation applications and packaging, every Streamline Line Set meets our rigorous standards for quality and consistency. With a broad offering of liquid line and suction line diameters, insulation, thicknesses, custom ends and connections plus a wide array of custom options, we're able to meet our customers' most specialized and exacting needs.
- 3/8 in. liquid line x 3/4 in. suction line x 3/8 in. insulation x 25 ft. L
- Copper tube UL recognized to 700 psi
- R410A engineered and tested
- Proprietary manufacturing process allows for kink-free installation
- Meets ASTM B1003
PRO-Fit Quick Connect fittings are designed to connect refrigerant lines without an open flame, brazing or swaging. They are suitable for joining refrigerant lines in seconds. After cutting the line, deburring the ends and push to connect.
- Quick and easy push-in
- Flame-free: no flaring or brazing needed
- Single use with quick release removal
- Leak-resistant double O-rings sealing
- Compatible with major refrigerants
Section 608 of the Federal Clean Air Act requires that all persons who maintain, service, repair or dispose of appliances that contain ozone depleting refrigerants be certified in proper refrigerant handling techniques. These regulations were revised in the Fall of 2016 to address HFCs, HFOs, revised allowable leak rates and expanded record keeping guidelines. The Esco Institute's EPA Section 608 Certification Program has been revised to incorporate these new regulations. Preparatory Manual 2019 The Esco Institute's EPA Section 608 Preparatory Manual covers the material required to successfully pass the Universal Exam in 32 pages. Introduction Federal Regulations Before You Begin Overview of the Examination Test Format Vapor-Compression Refrigeration Cycle How to Use the Pressure-Temperature Chart Refrigeration Service Gauge Manifold Set Tips for Taking Multiple-Choice Exams.
- Core stratospheric ozone depletion global warming potential refrigerant characteristics and identification bubble and dew points low, medium, high and very high pressure refrigerant oils Montreal protocol and clean air act recovery devices leak detection dehydration safety/general safety/cylinder shipping refrigerant characteristics chart
- Type I certification recovery equipment recovery requirements recovery techniques safety
- Type II Certification system Classifications Determining system charge leak repair requirements leak repair time frames section 608 leak repair regulations record keeping leak detection Recovery techniques: before you recover Recovery techniques: enhancing the process Recovery techniques: required evacuation levels during recovery Refrigeration system Liquid-Line accessories Refrigeration system suction line and compressor Accessories system Evacuation system charging and the pressure-temperature chart
- Type III certification leak detection leak repair requirements Recovery techniques recovery requirements Recharging techniques safety saturation chart back
Streamline Line Sets have been an industry leader for decades. We leverage our many years of experience and expertise producing copper tube in every line set we make. From liquid line and suction line handling to unique insulation applications and packaging, every Streamline Line Set meets our rigorous standards for quality and consistency. With a broad offering of liquid line and suction line diameters, insulation, thicknesses, custom ends and connections plus a wide array of custom options, we're able to meet our customers' most specialized and exacting needs.
- 3/8 in. liquid line x 3/4 in. suction line x 1/2 in. insulation x 35 ft. L
- Copper tube UL recognized to 700 psi
- R410A engineered and tested
- Proprietary manufacturing process allows for kink-free installation
- Meets ASTM B1003
SpeediChannel is an aesthetically pleasing and protective covering system for ductless mini-split line sets, drain lines, and control cables. This 6.5 ft. long channel will direct the line-set down the wall of the building and connects easily to other SpeediChannel Fittings. These covers are deal for applications where the lines cannot be hidden inside of a wall. The unique SpeediClip fittings and screw-in couplings provide durability and ease of installation -simple enough to be a one-person job. Founded in 1971, Diversitech Corporation is North Americas largest manufacturer of equipment pads and a leading manufacturer and supplier of components and related products for multiple industries, including: HVACR, electrical, consumer hardware retail, electrical utility, automotive retail and pool and spa channel. Diversitechs mission for its wholesaler partners is to simplify their work. We do this by offering more than 200 product categories all from a single manufacturing/supplier source to create product availability and supply chain cost advantages for our customers in every market we serve. We also leverage best-in-class customer service to react quickly and professionally to every customer request.
- SpeediClip slides into place allowing single person installation
- Paintable for custom appearance
- Natural color blends with almost any construction aesthetic
- Easy to use
This cylinder can be used for residential, commercial and automotive applications. It is used to recover, store and transport used refrigerant from any HVAC system to a location where it can be recycled and put back into service, or properly disposed of. Produced at the highest quality in the business.
- Grey/yellow cylinders feature Y valve for liquid/vapor recovery
- Tanks rated at 400 psi to handle 410A refrigerant
- Does not include IMO float gauge
- For use with recovery machine, yellow jacket #95762
Platinum 7 CFM vacuum pump, 115 volt, 60 Hz double stage. Check valve prevents oil backflow during power failure. Gas ballast valve prevents moisture and condensation.
- 2 stage direct drive
- 1/2 HP capacitor start and thermal overload protection
- 25 microns vacuum rating
- Field repairable
ONLY RESELLERS OR EPA-CERTIFIED TECHNICIANS CAN PURCHASE THIS PRODUCT. YOU MUST PROVIDE PROOF OF CERTIFICATION PRIOR TO ORDERING THIS REFRIGERANT PRODUCT
- Designed to ensure efficient cleaning
- Only Resellers or EPA certified technicians can buy refrigerant
- You also must provide proof of certification prior to receipt of order (not availalbe in all locations)
- Includes 5 pads in 1 case
PRO-Fit Quick Connect fittings are designed to connect refrigerant lines without an open flame, brazing or swaging. They are suitable for joining refrigerant lines in seconds. After cutting the line, deburring the ends and push to connect.
- Quick and easy push-in
- Flame-free: no flaring or brazing needed
- Single use with quick release removal
- Leak-resistant double O-rings sealing
- Compatible with major refrigerants
This cylinder can be used for residential, commercial and automotive applications. It is used to recover, store and transport used refrigerant from any HVAC system to a location where it can be recycled and put back into service, or properly disposed of. Produced at the highest quality in the business.
- Grey/yellow cylinders feature Y valve for liquid/vapor recovery
- Tanks rated at 400 psi to handle 410A refrigerant
- Does not include IMO float gauge
- For use with recovery machine, yellow jacket #95762
SpeediChannel is an aesthetically pleasing and protective covering system for ductless mini-split line sets, drain lines, and control cables. This Union Coupling joins together SpeediChannel Fittings. These covers are deal for applications where the lines cannot be hidden inside of a wall. The unique SpeediClip fittings and screw-in couplings provide durability and ease of installation, simple enough to be a one-person job. Founded in 1971, Diversitech Corporation is North Americas largest manufacturer of equipment pads and a leading manufacturer and supplier of components and related products for multiple industries, including: HVACR, electrical, consumer hardware retail, electrical utility, automotive retail and pool and spa channel. Diversitechs mission for its wholesaler partners is to simplify their work. We do this by offering more than 200 product categories all from a single manufacturing/supplier source to create product availability and supply chain cost advantages for our customers in every market we serve. We also leverage best-in-class customer service to react quickly and professionally to every customer request.
- UV resistant
- For indoor and outdoor use
- SpeediClips snap into channel to provide attachment points
- Easy to use
- E-FLEX GUARD AC line set insulation protectors
- Protector is U/V, fire rated, anti-microbial/fungal, PVC flexible material
- Removable/reusable, great for maintenance
- Quick installation with dual bonded velcro fasteners plus U/V cable ties for long term secure installation
- Complies with 2012 IECC energy codes
- 6 FT length
- Black